+86-020-23831672

Products Detail

Belt tunnel furnace

  • Belt tunnel furnace

Description

Painting equipment, also known as fuel injection equipment:

Paint spray equipment according to different: high-pressure air spraying, low-pressure air spraying, airless spraying, electrostatic spraying.

1. Airless spray: building decoration \ steel \ shipyard

2. Low-pressure air spraying: generators, power stations and so on

3.High-pressure air spraying: spray paint on the surface of workpiece through high-pressure air

⑴ by spraying methods Category: manual spraying, fixed gun rotating spraying, plane reciprocating machine spraying, spraying machine from top to bottom, robot spraying, DISC spraying

⑵ by delivery mode: chain type, the tunnel plane, hanging

⑶ workpiece: plastic, wood, glass, metal, ceramics, stone and so on

⑷ process:

① a coating of a baking (plastic products): → preheat (50 ℃, 3min) → automatic electrostatic dusting → fixed gun rotating spray → curing (60 ℃, 20min) → finished lower parts.

(50 ℃, 3min) → automatic electrostatic dusting → fixed gun spin coating → IR homogenization section (50 ℃, 5min) → fixed gun rotating spray → UV (plastic products) Light curing → finished lower parts.

③ a coating of a baking (glass): on → preheat (50 ℃, 3min) → automatic electrostatic dusting → fixed gun spin coating → curing (150 ℃, 20min) → cooling (5min) → finished lower parts.

④ two coating two roast: upper → preheat (50 ℃, 3min) → automatic electrostatic dusting → fixed gun spin coating → low temperature leveling (80 ℃, 5min) → fixed gun spin coating → curing (150 ℃, 20min) → Cooling (5min) → finished lower parts.

4. Electrostatic spraying:

(1) Overview: the use of electrostatic generator generates a negative voltage of 3-10 million volts through the gun head in the vicinity of the needle to form electrostatic field, the paint through a certain pressure to spray gun through the electrostatic field to bring negative charge, Sprayed workpiece ground to form a positive pole. In short, positive (workpiece) and negative (dusting) to attract each other, so that dust evenly fly to the surface, the utilization rate is very high, up to 90%. The traditional powder spraying adopts high pressure air direct spray, the utilization rate is only 30-40%.

⑵ workpiece: metal products (conductive objects), including iron products, aluminum products, stainless steel and so on.

Glass products (improved equipment to become conductive objects)

⑶ by spraying: manual electrostatic spraying, up and down reciprocating machine static, spray electrostatic spraying spin cup, DISC spraying

⑷ process (glass):

① a coating of a roast: upper → preheat (50 ℃, 3min) → automatic electrostatic dusting → rotating electrostatic spin coating → curing (150 ℃, 20min) → cooling (5min) → the next product.

② two coated two roasted: the upper → preheat (50 ℃, 3min) → automatic electrostatic dusting → rotating rotating electrostatic spray spin → low temperature leveling (80 ℃, 5min) → rotating electrostatic spin coating → curing (150 ℃, 20min ) → cooling (5min) → the next product.

5. Painting equipment, including: pre-treatment equipment, spray gun, paint room, oven, transmission line.

⑴ pre-treatment equipment (metal or glass products): trough-type pre-treatment, automatic processing line.

⑵ gun: air gun, electrostatic spray gun, rotating cup (hanging cup), DISC

  Air gun: Japan Iwata W-101, Polaroid, Ming Li

  Electrostatic spray gun: same, the Japanese Lan Shi

⑶ spray paint: cabinet, exhaust fan, water pump + water supply pipe, electronic control system

6. Auxiliary equipment: clean room, fresh air supply system, filtration equipment + Air Shower, duct, waste gas treatment, wastewater treatment.

7. Matching products: air compressor, pre-treatment syrup, oil paint, water-based paint, air spray gun, electrostatic painting, fixture, floor paint, waste water treatment AB agent.


More information
Should you have any questions regarding our products or require more information, please do not hesitate to contact us.